SCOTON

Mechanical Casing Running Tool (Internal) Casing running tool is a new technology for running casing. We developed the more safe and effi cient internal casing running too l to break the limitation of normal running casing operation. This technology could develop all the advantages of top drive drilling, make the casing string rotating, lift and circulating the mud simultaneously, insure the casing could be running to the well bottom normally, improve the success rate, safety and effi ciency of casing running observably. It has a wide introduction value to the oil field. Specification of Casing Running Tool (Internal) Model Casing Running Range (inch) ID mm (inch) Conn. Sealing load MPa Max tensile load K-N Max. Working torque (KN.m) OAL Mm(inch) MCRT 168 6- 5/8,7-5/8,8-5/8 50.8(2) 6-5/8REG 35 3200 26 2800 (110 1/2) MCRT 244 9-5/8,10-3/4,11-3/4 50.8(2) 6-5/8REG 35 4500 50 2935 (115 1/2) Casin...

Top drive floating cushion sub an important tool in drilling operation. It is suit to the drilling process in oil, gas and geological exploration. Mainly used for top drive drilling operation. It can increase the working life of bearing and gear in top drive rotary box. Specification of Top drive Floating Cushion Sub OD mm(inch) Upper Conn. Lower Conn. Lifting Force(T) Torque (KN • m) Stroke Mm(inch) OAL mm(inch) DQFC381(15) 6 5/8REG NC50 150 50 76(3) 798(30 13/32)

Top Drive Saver Sub is a kind of sub connected with Lower IBOP and drill pipe, mainly used in the top drive system. Not only acting as crossover sub, but also protecting lower IBOP. Top drive saver sub can be divided into general top drive saver sub and low temperature top drive saver sub. Specification of Top Drive Saver Sub Model OD mm(inch) ID mm(inch) Conn. DQA187B 187(7 23/64) 57.2(2 1/4) 6 5/8REG×NC46 DQA187A 187(7 23/64) 71.4(2 13/16) 6 5/8REG×NC50 DQA197B 197(7 3/4) 57.2(2 1/4) 6 5/8REG×NC46 DQA197A 197(7 3/4) 71.4(2 13/16) 6 5/8REG×NC50 DQA219A 219(8 5/8) 71.4(2 13/16) 7 5/8REG×NC50

IBOP for top drive can be divided into Upper IBOP and Lower IBOP, they are control valves which are used with the top drive system. Usually the two valves connected to the top drive drilling device. The inside BOP adopts high reliable metal seal. So it can bear high pressure upward and downward. The working pressure can be achieved 10000 psi or 15000 psi. When well kick occurring, the upper IBOP can be closed by remote controlled, but the lower IBOP will be closed manually. Actuator for top drive is a subsidiary body which controls open and close of Upper IBOP. It works with other accessories of the rig, so that control opening and closing of Upper IBOP on any height of derrick driller console. Both the valve body cavity and accessories have special anti-corrosive processing, so that prolong the working life. Specification of IBOP For Top Drive Model OD mm(inch) ID mm(inch) OAL mm(inch) Conn. STJ03M 187(7 23/64) 78(3 5/64) 572(22 33/64) 6 5/8REG BO...

The iron roughneck for sale consists of the main forceps and the knobs, which are able to buckle / shackle the string diameter range from 2-7 / 8 "to 10" and the full operation of the buckle / shackle is integrated in one Pneumatic control box, press the button once to complete all operations, while the pneumatic control box can be installed in a safe place to achieve remote control. The Miniscope which is used to position the iron roughneck, is a compact, lightweight device that is driven by a hydraulic cylinder to achieve the force in both directions - to stretch and push To promote the iron drill to the wellhead buckle, after the end of the iron drill back to the rest position. T-120 Iron Roughneck The new T-120 Iron Roughneck from SCOTON produce with maximized reach and takes it to an unprecedented level. Completely retractable, the tool extends just over 5 feet from the pivot, minimizing its footprint and leaving more room on the rig floor. Fully extended, the tool...

We have well organized and trained products Engineers, the quality of the products we offer are always kept at a high level. Extensive experience and expertise in most aspects of global equipment supply and services allows us to offer technical support that leads to added value for worldwide customers. With several year's experience, we have developed an extensive list of resources to find you the right equipment for the right price. All of the products we represent are approved or licensed by an accredited authority such as: API, NS, ANSI, DS, ISO or GOST. 100% compliance through consistent inspection and monitoring program. "Quality first, customer oriented and credit fundamental" is our business conception, it guide us put customer satisfaction always as our main priority. Every product from customer's inquiry to the delivery, also the after-sales service, we are follow up closely. Strict quality inspection system ensure our best quality for you, all kinds of tran...